IE Protection Device & Chip Shield

LED recessed luminaire TUBELED_40 II INTEGRATED - proven LED machine luminaire in the built-in version, suitable for all common installation shafts in machine tools. The integrated recessed luminaire has protection class IP67 / IP69K. It is made for harsh production environments and impresses with its enormous amount of light power and high light output. The emitted 100 ° area light is amplified with light forming technology in the direction where it is needed. The TUBELED_40 II Integrated recessed luminaire is 100% CNC suitable, because the built-in version of the TUBELED_40 II, with its robust housing and safety glass, is resistant to chip bombardment as well as coolants and lubricants.  Advantages: Bright and flicker-free illumination, without UV and IR components Generous lighting through 100 ° surface light Space-saving geometry: fits into common installation slots Easy and quick retrofitting of Machines High degree of protection IP67 / IP69K ON / OFF interface: load-free switching, flashing, flashing and dimming possible  Areas of application : Machine tools Woodworking machines Packaging machines Injection molding machines  Features: High-performance LED chips for daylight white 5200-5700 K Luminous flux-optimized light yield and flicker-free illumination without UV and IR components Beam angle 100 ° and good color rendering abe Ra> 85 Crack-proof, 4 mm thick ESG with opal white glare control Protection class IP67 / IP69K and above-average service life> 60,000h (L80 / B10) More direct Connection to machine or system voltage 24V DC via M12 plug connections Chip bulletproof, vibration and shock resistant - 100% CNC suitable Recessed luminaire for recess, sealed and screwed over cover Oil-resistant, sprayed-on seals Light Forming Technology for light guidance Heat dissipation via the rear profile - no burning in of coolants and lubricants CE and ETL listed test seals Maintenance-free, 36 months warranty Made in Germany  Versions: Panel width 74 mm in 4 Lengths: 220 mm, 395 mm, 570 mm, 745 mm Panel width 78 mm in 2 lengths: 340 mm, 700 mm All variants are only 3 mm thick when installed  

TUBELED_40 II LED machine light IP 67 / IP69K. The TUBELED_40 II is a machine light for rough production conditions and temperatures up to + 60 ° C. With a light diameter of only 40 mm, the slim machine light is an all-round talent - in terms of light output and possible applications. Available in 7 lengths and cascadable variants (can be linked electrically).  Advantages: Bright and flicker-free lighting, without UV and IR components Generous light exit area and 100 ° Area light Slim housing and various lengths Quick and easy equipping and retrofitting of machines and systems Temperature-resistant and splash-proof Height Degree of protection IP67 / IP69K Also for high ambient temperatures Electrically linked versions (cascadable) On / off interface. Load-free switching, flashing, flashing, dimming possible  Areas of application: Plastics processing Metal processing: micro-precision machines, eroding machines, stamping automation Woodworking with tight installation spaces  Features: High-performance LED chips for daylight white 5200-5700K - very bright beam angle 100 ° and good color rendering Ra> 85 protection class IP67 / IP69K and above-average service life> 60,000h (L80 / B10) crack-proof, 4 mm Strong ESG with opal white glare control Chip bulletproof, vibration and shock resistant - 100% CNC suitable Luminous flux-optimized power versions and performance-optimized ECO versions High total luminous flux, depending on the version Light-Forming-Technology Oil-resistant seals (FKM seal Vition®) Direct connection voltage 24V DC and cascading via M12 plug connections Practice heat dissipation r Aluminum extruded profile - no KSS burn-in CE - and ETL listed seal of approval Attachment via separately available accessories Maintenance-free, 36 months warranty Manufactured in Germany  Versions: 7 lengths: 190 mm, 280 mm, 365 mm, 540 mm, 715 mm, 1040 mm, 1540 mm 2 versions: Luminous flux-optimized power versions and power-optimized ECO versions Variants for electrical interlinking (cascadable)  

The LED system light UNILED SL RGB-W with signal function is a powerful system light which, in addition to balanced lighting, also offers a signal function for changing the light color or by flashing. The opal white glare control creates a homogeneous, glare-free and shadow-free illumination with a strong light output at the same time. Changes in status in the work area can be signaled by a color change, for example to green or red light or by intermittent flashing. Advantages: Homogeneous, low-shadow, glare-free illumination without UV and IR components Pleasant atmosphere thanks to daylight white 52005700K and signal function via different colors The white light reproduces colors and contrast values very well Opal white glare control for glare-free illumination Signaling via change of light color or intermittent flashing Integrated fastening straps Areas of application: Optical control workstations System workplaces Test and laboratory workplaces Color and lacquer tests Can be used in machines without coolant and chip bombardment Features: Robust aluminum housing with integrated fastening for horizontal use High-performance LED cluster with s Separate LED chips for white light and RGB Optionally also pivotable with wall or joint angles Bright illumination of system workstations and work areas with 5200-5700 K daylight white cover with opal white glare control Beam angle 100 ° and color rendering Ra> 85 in daylight white Signaling via change of light color - all colors of the RGB color space can be selected Protection class IP 50 and above-average service life> 60,000h (L80 / B10) Heat is dissipated to the rear via an aluminum base Connection voltage 24V DC via standardized M12 plug connection CE - and ETL listed seal of approval Maintenance-free, 36 months warranty Made in Germany Versions: Four different Lengths: 295 mm, 545 mm, 1045 mm, 1545 mm Different light intensities Opal white glare control

The powerful LED machine lamps of the Clik series provide bright, flicker-free light directly at your workplace. Equipped with 6 LEDs with 2W of each this LED lamp brings a total of 1.080lm and is available in 3 different sizes. You can focus the 60 degree light angle directly on your work surface by means of comfortable wing screws. The versions with articulated arm also allow easy alignment of the industrial luminaire. The ergonomic on/off switch also supports you in simple operation. In addition, the lamp has a built-in LED driver and a 2-pole cable, which has a 240V version with a Schuko plug. The 24V version can be connected directly to the machine electrical system. Angles and clamps for mounting are available as optional accessories.   These LED lamps are also ideal for retrofitting on: turning machines, plants for mould making grinding machines milling machines and other workplaces The materials used are highly resistant aluminium and robust glass. You will receive a tested product that complies with CE and RoHS standards and meets IP65.

The powerful LED machine lamp of the Clik Cob series is the new 20W version of the successful Clik LED lamps.Equipped with 1 LED with 20W LED, this industrial luminaire brings a total of 2,600lm and is available in 3 different sizes. You can focus the 60 degree light angle directly on your work surface by means of comfortable wing screws. The ergonomic on/off switch also supports you in simple operation. In addition, the lamp has a Schuko plug and an built-in LED driver in the lamp base. Angles and clamps for secure mounting of the industrial luminaire are optionally available as accessories.  These LED lamps are also ideal for retrofitting on: turning machines, plants for mould making grinding machines milling machines and other workplaces The materials used are highly resistant aluminium and robust glass. You will receive a high quality product that complies with CE and RoHS standards and meets IP65.

Emergency stop boxes with distribution box, suitable for a load up to 18 kW, 3 phases and 38 A.Three-phase motor start/stop with overload cut-off and automatic reset by push button or emergency stop switch.  The power is switched through to the load via protection C1. The distribution box has generated its own 400 V AC transformer TM1 of 24 V AC. The input and output circuits are fused. This auxiliary voltage is used to supply the emergency stop box, relay R1 and protection C1. Control functions for low voltage (24V), management of safety microswitches installed on the machine button.  All emergency stop boxes ensure conscious switching on and off without automatic restart. The built-in LED indicates whether voltage is applied to the box and thus to the machine. The emergency stop as well as the start/stop can be integrated into the existing machine stop circuit or make it possible in the first place.  Dimensions: L 170 x W 118 x H 82 mm (pushbutton panel) L 200 x W 150 x H 150 mm (switch box)Scope of supply: Pushbutton box and switch box, CE Declaration of Conformity

Emergency stop boxes, suitable for a load up to 2.2 kW 3 phases or 5.5 A 1 phase.Three-phase motor start/stop with overload cut-off and automatic reset by push button or emergency stop switch.  Relay K7 directly switches the power to the load. The emergency stop box has generated its own 400 V AC transformer TM of 24 V AC. The output circuit is protected by a fuse. The emergency stop boxes and relay K7 are supplied with this auxiliary voltage. Control functions for low voltage (24V), management of safety microswitches installed on the machine button.  All emergency stop boxes ensure conscious switching on and off without automatic restart. The built-in LED indicates whether voltage is applied to the box and thus to the machine. The emergency stop as well as the start/stop can be integrated into the existing machine stop circuit or make it possible in the first place.  Dimensions: L 170 x W 118 x H 82 mmScope of supply: Pushbutton box, CE Declaration of Conformity

Mobile back panel for lathes 1AB with steel frame and transparent, shockproof screen with grid to protect the operator against chips and coolant. Adaptable to almost all lathes and equipped with 4 wheels. Dimensions on request. Weight approx. 20 kg. Thickness of polycarbonate screen: 4 mm.  Conformity according to manufacturer: EN ISO 12100:2010, EN ISO 14120:2015, EN ISO 14119:2013.

Double safety levers under headstock and carriage LE/2. Conformity according to manufacturer: EN ISO 12100. Accessory for our lathe protective devices. Dimensions see technical details.

Electric safety foot pedal for lathes 1PED for switching off the machine.   Features: Weight: 2 kg Microswitch: IP67 safety microswitch B10d value: 20,000,000 cycles   Conformity to manufacturer: EN ISO 12100:2010, EN ISO 14120:2015, EN ISO 14119:2013, EN 60947-5-1:2017